Glossary of Terms

Industry Terminology

Think of this as your door dictionary. Refer to this section to familiarize yourself with common terms you may come across while making your door selection.

The following definitions are extracted from WDMA I.S.lA-11, Industry Standard for Architectural Wood Flush Doors and WDMA I.S.6A-1 1, Industry Standard for Architectural Stile and Rail Doors.

*These definitions are not included in current industry standards, however, they are common industry terms.

  • a
  • Astragal

    This moulding includes two different types, a T-Astragal and a Flat Astragal. Both are attached to one of a pair of doors to keep the other door from swinging through the opening. The flat astragal, can also be used for decorative purposes to cover a joint or separation.

  • b
  • Balanced Match

    Two or more veneer components or leaves of equal size (prior to edge trimming) to make up a single face.

  • Bar

    A narrow, horizontal, vertical, or diagonal wood member extending the total length or width of a glazed opening, used to separate individual pieces of glazing.

  • Barber Pole

    An effect in book matching of veneers. Because the “tight” and “loose” sides alternate in adjacent veneer leaves, they may accept stain or reflect light differently, resulting in a noticeable but acceptable color variation. Barber Pole is not considered a manufacturing defect.

  • Bark Pocket

    Comparatively small area of bark around which normal wood has grown.

  • Base Cap

    A decorative member installed flush against the wall and the top of an S4S baseboard. Also a versatile panel moulding.

  • Base Shoe

    Applied where base moulding meets the floor to protect the base moulding from damage by cleaning tools and conceals any uneven lines or cracks where base meets the floor.

  • Batten

    A symmetrical pattern used to conceal the line where two parallel boards or panels meet.

  • Bevel

    A machine angle other than a right angle, i.e., a 3 degree bevel that is equivalent to a 1/8 inch drop in a 2 inch span (1 mm in 16 mm).

  • Beveled Edge

    An edge of the door which forms an angle of less than 90 degrees with the face of the door, such as a 3 degree beveled edge.

  • Bladder Pressed Panel

    See “Membrane Pressed Panel”.

  • Blended Repair Tapering

    A repair referring to end splits, repaired with wood or filler similar in color to blend well with adjacent wood.

  • Blending

    Color change that is detectable at a distance of 6ft. to 8ft. (1.8m to 2.4m) but which does not detract from the overall appearance of the door.

  • Blind Mortise and Tenon

    A method of construction of stile and rail wood doors where openings are machined into, but not through the stiles and where the ends of the rails are so machined as to fit these openings.

  • Blister

    Spot or area where veneer does not adhere.

  • Blocking

    A material used to replace core material in specific locations to provide improved screw holding for the attachment of hardware. Blocking is only required where the screw holding power of the core is less than required by the applicable performance duty level.

  • Bonded Core

    Stiles and rails (edge bands) are securely glued to the core prior to application of crossbanding, three ply skins, veneers or laminate.

  • Book Match

    Adjacent leaves of veneer from a flitch or log are opened like a book and spliced to make up the face with matching occurring at the spliced joints. The fibers of the wood, slanting in opposite directions in the adjacent leaves, create a characteristic light and dark effect when the surface is seen from an angle.

  • Book Size

    The height and width of a door prior to prefitting.

  • Bow

    A flat wise deviation from a straight line drawn from top to bottom; a curvature along the length of the door.

  • Burl

    A swirl, twist or distortion in the grain of the wood, which usually occurs near a knot or crotch. A burl can often be associated with abrupt color variation and/or a cluster of adventitious buds.

  • Burl, Blending

    A swirl, twist or distortion in the grain of the wood which usually occurs near a knot or crotch but does not contain a knot and does not contain abrupt color variation.

  • Butt Joint

    A joint formed by square edge surfaces (ends, edges and faces) coming together; end butt joint, edge but/joint.

  • c
  • Cathedral Grain

    A grain appearance characterized by a series of stacked and inverted ‘V’s, or cathedral type of spring wood (earlywood) summerwood (latewood) patterns common in plain sliced (flat cut) veneer (see split heart).

  • Center Match

    An even number of veneer components or leaves of equal size (prior to edge trimming) matched with a joint in the center of the panel to achieve horizontal symmetry.

  • Certified Wood

    Wood products that have been qualified by an independent third party agency as satisfying their proprietary requirements for responsible environmental practices.

  • Chair Rail

    An interior moulding applied about a third up the wall from the floor, paralleling the base moulding and encircling the perimeter of a room. Originally used to prevent chairs from marring walls. Used today is as a decorative element or a divider between different wall covering such as wallpaper and paint or wainscoting.

  • Champher Strip

    A triangular moulding often used in concrete forming work to support the corners of the forms.

  • Chatter

    Line appearing across the face at right angles to the grain giving the appearance of one or more corrugations resulting from bad setting of sanding equipment.

  • Checks

    Small slits running parallel to grain wood; caused chiefly by strains produced in seasoning and drying.

  • Clustered

    When a defect described in the grading rule is sufficient in number and sufficiently close together to appear to be concentrated in one area.

  • Compatible

    When relating door edge to face appearance, the edge may not be the same species as the face; however, it may be similar in overall color, grain, character and contrast as the face (See Matching Edge Band).

  • Component (Of Face Veneer)

    An individual piece of veneer or leaf that is joined to other pieces to achieve a full length and width face.

  • Composite

    A composite whose ingredients include cellulosic elements. These cellulosic elements can appear in the form of but are not limited to: distinct fibers, fiber bundles, particles, wafers, flakes, strands and veneers. These elements may be bonded together with naturally occurring or synthetic polymers. Also, additives such as wax or preservatives may be added to enhance performance.

  • Composite Panel

    A door panel composed of a wood derivative such as MDF. Used for opaque finishes.

  • Coped Construction

    The end of rails, mullions, muntins or bars so machined that they will fit and cover the contour of the sticking.

  • Core

    The innermost layer or section in component construction. For typical constructions see: Particleboard Core, Medium Density Fiberboard Core, Structural Composite Lumber Core, staved Lumber Core, Laminated Veneer Lumber Core, Fire Resistant Composite Core and other special core types.

  • Core, Fire Resistant

    A fire resistant core material generally used in wood doors requiring fire ratings of 3/4 hour or more. Engineered composite products meeting the minimum requirements of WDMA.

  • Cross Bar (veneer)

    Irregularity of grain resembling a dip in the grain running at right angles, or nearly so, to the length of the veneer.

  • Cross Break

    Separation (break) of the wood cells across the grain. Such breaks may be due to internal strains resulting from unequal longitudinal shrinkage, or to external forces.

  • Cross Figures

    A series of naturally occurring figure effects characterized by mild or dominant patterns across the grain in some faces. For example, a washboard effect occurs in fiddle-back cross figure; and cross wrinkles occur in the mottle figure.

  • Crossbanding

    A ply placed between the core and face veneer in 5-ply construction or a ply placed between the back and face of a 3-ply skin in 7-ply construction, typically of hardwood veneer or engineered wood product.

  • Cup

    A deviation from a straight fine drawn from side to side; a curvature along the width of the door.

  • d
  • Dead Knots (Open Knots)

    Openings where a portion of the wood knot has dropped out or where cross checks have occurred to present an opening.

  • Defect, Open

    Checks, splits, open joints, knotholes, cracks, loose knots, wormholes, gaps, voids or other opening interrupting the smooth continuity of the wood surface.

  • Delamination

    Separation of plies or layers of wood or other material through failure of the adhesive bond.

  • Discolorations

    Stains in wood substances. Some common veneer stains are sap stains, blue stains, stain produced by chemical action caused by the iron in the cutting knife coming into contact with the tannic acid in the wood and those resulting from the chemical action of the glue.

  • Door Frame

    A group of wood parts machined and assembled to form a door enclosure from which and exterior door is hinged.

  • Door, Bifold

    Doors so hinged as to fold against the door jamb. Bifold doors are normally classified as either two-or four-leaf units.

  • Door, Combination

    A door assembly of stiles and rails that will include multiple door types within a single door. These door types would typically include combinations of flat or raised panels, lites and/or louvers.

  • Door, French

    A door assembly of stiles and rails (and possibly muntins and bars) surrounding a single or multiple glazed opening.

  • Door, Louver

    A door assembly of stiles and fails where the interior is filled with slat or chevron louvers.

  • Door, Panel

    A door assembly of stiles, rails and one or more panels. Intermediate rails or mullions are used to separate panels. Panels can be raised or flat.

  • Doweled Construction

    A method of construction of stile and rail wood doors where holes are machined into, but not through, the stiles and where matching holes are machined into the ends of the rails. Glue and dowels are inserted into these holes to attach the rail to the stile.

  • e
  • Edge Band

    A strip along the outside edges of the two sides and/or top and bottom of the door (See stiles/vertical edges, rails/horizontal edges).

  • End Match

    A door/transom combination where single piece of veneer extends from the bottom to the top of the door with a mirror image at the transom.

  • Engineered Construction

    A method of constructing a wood stile and rail door that minimizes the use of solid lumber components. Stiles, rails and mullions have solid lumber edges only (where visible), and have face veneers over a composite core. Panels are also produced using face veneers and/or composite cores.

  • Engineered Materials

    A general term used to describe any wood or plant fiber composite panel. Such products as Particleboard, MDF, SCL and LVL are described as Engineered Fiber. Typically they are made from wood or plant fiber or wood pieces and have specific quality requirements.

  • Engineered Veneer

    Veneers that are first peeled, normally from Obeche or Poplar logs. The peeled veneer/eaves are dyed to a specified color, and then glued together in a mold to produce a large laminated block. The shape of the mold determines the final grain configuration. The block is then sliced into leaves of veneer with a designed appearance that is highly repeatable.

  • f
  • Face Veneer

    The outermost exposed wood veneer surface of a veneered wood door.

  • Face Width

    The total width of the stile, rail or panel minus the width of the moulding patterns. The most common way of showing dimensions on a stile and rail door elevation.

  • Few

    A small number of characteristics without regard to their arrangement in the panel.

  • Fill (Putty Repairs)

    A repair to an open defect usually made with fast drying plastic putty. The repairs should be well made with non-shrinking putty of a color matching the surrounding area of the wood, to be flat and level with the face and panel, and to be sanded after application and drying.

  • Finger Joint

    A joint made by cutting away interlocking fingers in the ends of two adherends and bonding the adherends with the cut areas fitted together to form longer pieces.

  • Fire Rated Doors

    A door which has been constructed in such a manner that when installed in an assembly will pass a fire test under neutral (UL 108) or positive (UL 10C) pressure criteria and can be rated as resisting lire for 20 minutes (1/3 hour), 45 minutes (3/4 hour), 1 hour or 1

  • Fire Resistant Composite Core

    A core, typically incorporating minerals rather than wood fiber as the primary component, designed to improve fire resistance and thermal transmission.

  • Fleck, Ray (Flake)

    Portion of a ray as it appears on the quartered or rift cut surface. Fleck can be dominant appearance in oak and is sometimes referred to as flake.

  • Flitch

    A complete bundle of veneer sheets laid together in sequence as they are cut from a given log or section of log.

  • g
  • Gaps

    Open slits in the inner ply or plies or improperly joined veneer when joined veneers are used for inner plies.

  • Glass Stop

    A small wood moulding (bead) applied to the perimeter of glazed openings to secure the glazing materials within a door.

  • Grain

    The direction, size, arrangement and appearance of the fibers in wood or veneer.

  • Grain Slope

    Expression of the angle of the grain to the long edges of the veneer component.

  • Grain Sweep

    Expression of the angle of the grain to the long edges of the veneer component over a 12 inch (300 mm) length from each end of the door.

  • Gum Pockets

    Well defined opening between rings of annual growth containing gum or evidence of prior gum accumulations. Mainly cherry.

  • Gum Spots & Streaks

    Gum or resinous material of color spots caused by prior resin accumulations sometimes found on panel surfaces.

  • h
  • Hairline

    A thin, perceptible line showing at the joint of two pieces of wood.

  • Half Round

    A moulding with a profile that is a half circle with many purposes such as shelf edge, panel mould, screen mould or a bead.

  • Hardboard

    Homogeneous panels manufactured primarily from inter-felted lignocellulosic (wood) fibers consolidated under heat and pressure with density of 31lb/ft3 (497 kg/m3) or more.

  • Hardwood

    Hardwoods are one of the botanical groups of trees that have broad leaves in contrast to the needle-like leaves of the conifers or softwoods.

  • Heartwood

    The non active center of a tree generally distinguishable from the outer portion (sapwood) by its darker color.

  • Holes, Worm

    Holes resulting from infestation by worms greater than 1/16inch (1.6mm) in diameter and not exceeding 5/8inch (16mm) in length.

  • i
  • Inconspicuous

    Barely detectable with the naked eye at a distance of 6ft. to 8ft. (1.8m to 2.4m).

  • Indentations

    Areas in the face that have been compressed as the result of residue on the platens of the hot press or handling damages.

  • Intumescent

    A material that expands when exposed to extreme heat or fire to fill any gap between the door and frame or between doors.

  • j
  • Joint

    The line of juncture between the edges or ends of two adjacent pieces of veneer.

  • Joint, Edge

    Joint running parallel to the grain of the wood.

  • Joint, Open

    Joint in which two adjacent pieces of veneer do not fit tightly together.

  • k
  • Kiln-Dried

    Lumber dried in a closed chamber in which the removal of moisture is controlled by artificial heat and usually by controlled relative humidity.

  • Knife Cuts Per Inch (KCPI)

    A measure of the smoothness of machined lumber. Can be determined by holding the surfaced board at an angle to a strong light source and counting the visible ridges per inch, usually perpendicular to the profile. The surface is smoother with more knife marks per inch.

  • Knife Marks

    Very fine lines that appear across the panel veneer or wood solids that can look as though they are raised resulting from some defect in the lathe knife that cannot be removed with sanding.

  • Knot

    Cross section of tree branch or limb with grain usually running at right angles to that of the piece of wood in which it occurs.

  • Knot Holes

    Voids produced when knots drop from the wood in which they were originally embedded.

  • Knots, Conspicuous Pin

    Sound knots 1/4inch (6.4mm) or less in diameter containing dark centers.

  • Knots, Open (Knot Holes)

    Openings where a portion of the wood substance of the knot was dropped out, or where cross checks have occurred to produce an opening.

  • Knots, Sound Tight

    Knots that are solid across their face and fixed by growth to retain their place.

  • Knots. Blending Pin

    Sound knots 1/4 inch (6.4 mm) or less that generally do not contain dark centers. Blending pin knots are barely detectable at a distance of 6ft. to 8ft. (1.8 m to 2.4 m), do not detract from the overall appearance of the panel, and are not prohibited from appearing in all grades.

  • l
  • Laminated Veneer Lumber Core (LVLC)

    Manufactured by laminating veneer with all grain laid-up parallel. It can be manufactured by using various species of wood fiber in various thicknesses.


  • Lap (Veneer)

    A condition where the pieces of veneer are so misplaced that one piece overlaps the other and does not make a smooth joint.

  • Lock Block

    A concealed block the same thickness as the door stile or core which is adjacent to the stile at a location corresponding to the lock location and into which a lock is fitted.

  • Loose Side

    In knife-cut veneer, that side of the sheet that was in contact with the knife as the veneer was being cut, and containing cutting checks (lathe checks) because of the bending of the wood at the knife edge.

  • Louver

    A panel constructed of wood or metal slats installed in an opening to allow light, air and noise. Common types are slat and Chevron – an inverted “V” wood louver (vented or non-vented).


  • Low Pressure Decorative Laminate

    A decorative surface paper that is saturated with reactive resins. During hot press lamination, the resin flows into the surface of the substrate, creating a hard crosslinked thermosetting permanent bond and permanently changing the characteristics of both the paper and the board.

  • m
  • Match Edge Band (ME)

    An edge band that is the same species or laminate pattern as the face veneer.

  • MatchRunning m

    The veneer face is made from components running through the flitch consecutively. Any portion of the component left over from a face is used as the beginning component or leaf in starting the next veneer face.

  • Medium Density Fiberboard (MDF)

    The generic name for a panel or core manufactured from lignocellulosic fibers combined with a synthetic resin or other suitable binder and bonded together under heat and pressure in a hot press by a process in which the added binder creates the entire bond.

  • Medium Density Fiberboard Core (MDFC)

    Wood fiber and/or agri-fiber based materials that comply with ANSI A208.2.

  • Medium Density Overlay (MDO)

    Typically MDO is kraft paper saturated with resin and cured under high heat and pressure to make a hard, smooth, paintable surface.

  • Meeting Edges

    Two adjacent door edges not separated by a mullion or transom bar. These are found in pair, Dutch door and door & transom applications.

  • Membrane (Bladder) Pressed Pane

    Insert panel produced by moulding to profile a wood or composite core (usually MDF or particleboard) then pressing veneer to the core using a flexible pressing surface.

  • Mineral Stain

    Olive and greenish-black streaks believed to designate areas of abnormal concentration of mineral matter; common in hard maple, hickory, and basswood. Also called Mineral Streak.

  • Mineral Streaks

    Sharply contrasting elongated discoloration of the wood substance.

  • Moulding (Inlay)

    Profiled wood trim pieces that surround the perimeter of panels or glazing, but does not protrude above the surface of the surrounding stiles and rails.

  • Moulding (Overlay)

    Profiled wood trim pieces that surround the perimeter of panels or glazing, and protrudes above the surface of the surrounding stiles and rails.

  • Mullion

    A vertical member used to separate panels. Also known as a “mull.”

  • Muntin

    A short bar, either horizontal or vertical, used to separate individual pieces of glazing material, but which does not extend the full width or length of the glazed opening. Also known as “munt”.

  • n
  • Natural

    When referring to color and matching, veneers containing any amount of sapwood and/or heartwood, i.e., natural birch maple, ash.

  • Neutral Pressure

    A fire door test procedure where the neutral pressure plane is near the top of the door.

  • Nominal

    A term that designates a stated dimension as being approximate and subject to allowances for variation.

  • Non-Bonded Core

    Stiles and rails (edge bands) are not glued to the core prior to face materials.

  • p
  • Panel, Flat

    A door panel in which the perimeter does not contain a machined profile (panel raise). Constructed with veneer on the face and a composite core for a stained finish, or MDF for a painted finish.

  • Panel, Raised

    A door panel whose faces are raised above the perimeter and whose edges are shaped to fit into grooves in the stiles, rails and mullions. These panels are typically bladder pressed or rim banded for a stained finish or MDF for a painted finish.

  • Particle Board

    A panel or core product composed of small particles of wood and wood fiber that are bonded together with synthetic resin adhesives in the presence of heat and pressure.

  • Particleboard Core

    Wood fiber and/or agri-fiber based materials that comply with ANSI A208.1, minimum grade LD-1.

  • Patches

    Matching wood pieces carefully inserted and glued into the door face after defective portions have been removed.

  • Plain Sliced

    Veneer sliced parallel to the pith of the log and approximately tangent to the growth rings to achieve flat cut veneer. Plain sliced veneer can be cut using either a horizontal or vertical slicing machine or by the half-round method using a rotary lathe. Also known as flat cut.

  • Plank Matched

    A face containing specially selected and assembled dissimilar (in color, grain and width) veneer strips of the same species, and sometimes grooved at the joints between strips, to simulate lumber planking. Plank matched faces are not available pair matched or set matched.

  • Pleasing Match

    A face containing components, which provide a pleasing overall appearance. The grain of the various components need not be matched at the joints. Sharp color contrasts at the joints of the components are not permitted.

  • Ply

    A single sheet of veneer or several strips laid with adjoining edges that may or may not be glued, which forms one veneer lamination in a glued panel. In some constructions, a ply is used to refer to other wood components such as particleboard or MDF.

  • Positive Pressure

    A fire door test procedure where the neutral pressure plane is located at 40 inches (1m) above the sill.

  • Prefitting

    Trimming of the door for width and/or height.

  • q
  • Quartered (Quarter-sliced, Quarter Cut)

    Veneer produced by cutting in a radial direction to the pith to achieve a straight (vertical) grain pattern. In some species, principally red oak and white oak, ray fleck is produced, the amount of which may be unlimited.

  • r
  • Rail

    A horizontal structural member of a stile and rail door. Fits between the stiles.

  • Rail, Bottom

    The bottom rail of a stile and rail door.

  • Rail, Intermediate

    A rail, other than the top and bottom rail, used to separate panels, or to separate panels from glazing materials in a combination door. Also referred to as “cross rail.”

  • Rail, Lock

    An intermediate rail located at approximately adjacent to the Jock.

  • Rail, Top

    The uppermost rail of a stile and rail door.

  • Rail/ Horizontal Edges

    Top and bottom edge bands of door.

  • Random Matched (Mismatched)

    A face containing veneer strips of the same species which are selected and assembled without regard to color or grain, resulting in variations, contrasts and patterns of color and grain. Pleasing appearance is not required. Random matched faces are not available pair matched or set matched.

  • Ray

    Ribbon-shaped strand of tissue extending in a radial direction across the grain, so oriented that the face of the ribbon is exposed as a fleck on the quarter surface. Also known as Wood Ray.

  • Red/Brown

    When referring to color and matching, veneers containing all heartwood, ranging in color from light to dark.

  • Repairs

    A patch, shim, or filler material inserted and/or glued into veneer or a panel to achieve a sound surface.

  • Repairs, Blending

    Wood or filler insertions similar in color to adjacent wood so as to blend well.

  • Rift Cut

    Veneer produced by cutting at a slight right angle to the radial to produce a parallel grain pattern and quartered appearance without excessive ray fleck. Oak veneer only.

  • Rim Banded (Mitered) Panel

    Insert panel with a solid lumber edge banded around the core then veneered and profiled.

  • Rotary Cut

    Veneer produced by centering the entire log in a lathe and turning it against a broad cutting knife.

  • Rough Cut

    Irregular shaped areas of generally uneven corrugation on the surface of veneer.

  • Ruptured Grain

    A break or breaks in the grain or between springwood and summerwood caused or aggravated by excessive pressure on the wood by seasoning, manufacturing, or natural processes. Ruptured grain appears as a single or series of distinct separations in the wood such as when springwood is crushed leaving the summerwood to separate in one or more growth increments.

  • Rustic

    Lacking excessive refinement, having a rough surface or finish.

  • s
  • Safety Glazing Materials

    Glazing materials so constructed, treated or combined with other material as to minimize the likelihood of cutting or piercing injuries resulting from human contact with the material. The most common types used in doors are tempered or laminated. Safety glazing materials are required to meet codes and federal regulations.

  • Sanding (Chatter, Dust, Bums)

    The degree of defects allowed in sanding of the face.

  • Sapwood

    Outer layers of growth between the bark and the heartwood which contain the sap.

  • Shake

    A separation along the grain of wood in which the greater part occurs between the rings of annual growth.

  • Sharp Contrast

    For the purpose of this standard, this term means the veneer of lighter than average color should not be joined at the edges with veneer of darker than average color, and that two adjacent pieces of veneer should not be widely dissimilar in grain, figure and natural character markings.

  • Shims

    A split repaired in a piece of wood veneer, preferably from the same piece of veneer from which the face is made to ensure good color and grain match. The grain running in the same direction as the split to be inconspicuous to the naked eye, and free of any gaps where the shim joins the veneer. To be glued into the split and sanded after being made. Color matched.

  • Show Through (Telegraphing)

    A defect caused by the outline and/or surface irregularities, such as frame parts, core laps, voids, etc., that is visible through the face veneers.

  • Skin

    The face layer of a flush or stile and rail door, whether flat or configured, which is used for facings for flush wood doors.

  • Sliced

    Veneer produced by thrusting a log or sawed flitch into a slicing machine, which shears off veneer in sheets.

  • Slight

    Visible on observation, but does not interfere with the overall aesthetic appearance.

  • Slip Heart

    A method of achieving an inverted V or cathedral type of springwood (earlywood) summerwood (latewood), plain-sliced (flat-cut) figure by joining two veneer components of similar color and grain. A cathedral type figure must be achieved by a single component in M grade; the split heart method is allowed in grades A and B. Each half of a split heart shall be subject to the minimum component width requirements for grade A and B faces.

  • Slip Matched

    A sheet from a flitch is slid across the sheet beneath and, without turning, spliced at the joint.

  • Smooth, Tight Gut

    Veneer cut to minimize lathe checks.

  • Splits

    Separations of wood fiber running parallel to the grain.

  • Splits, Hairline

    A perceptible separation or absence of wood fiber running parallel with the grain.

  • Standard Door

    By industry practice, a standard door is book size in both width and height.

  • Sticking

    A profile machined on to the edges of stiles, rails, mullions, muntins or bars, adjacent to the panels, glazing materials or louvers.

  • Stile

    The outermost vertical member of a stile and rail door.

  • Stiles/Vertical Edges

    The upright or vertical pieces of the core assembly of a wood flush door. Measurement. The width of the vertical edge/stile is measured at its widest side (the wide side of a beveled door).

  • Streaks, Mineral

    Sharply contrasting elongated discoloration of the wood substance.

  • Structural Composite Lumber Core (SCLC)

    An engineered wood product that is made by fusing a network of wood strands together with a water-resistant adhesive to produce a strong, solid and stable product that has true structural properties with excellent screw holding properties and very high split resistance.

  • t
  • Tape

    Strips of gummed paper used to hold the edges of the veneer together at the joints prior to gluing.

  • Tight Side

    In knife-cut veneer, that side of the sheet that was farthest from the knife as the sheet was being cut and containing no cutting checks (lathe checks).

  • Transom

    The panel above a door or set of doors.

  • Twist

    A deviation in which one or two corners of the door are out of plane with the other corners of the door.

  • v
  • Veneer (wood)

    A thin sheet of wood, rotary cut, sliced, or sawed from a log, bolt, or flitch.

  • Vine Streaks (Mark)

    Scars in the wood generally caused by the stems of clinging vines or by their hair-like roots, which cling to the tree trunk. Live vine streaks produce round scars. Dead vine streaks contain either dead residue of the vine, or the remaining pocket similar to bark pocket. Most vine streaks run across the grain, and therefore, all vine streaks are considered defects in accordance with restrictions described in veneer grading rules.

  • w
  • Warp

    Any distortion in the plane of a door itself and not its relationship to the frame or jamb in which it is to be hung. The term warp includes bow, cup and twist, which are defined as follows: Bow-A flat wise deviation from a straight line drawn from top to bottom; a curvature along the length of the door. Cup-A deviation from a straight line drawn from side to side; a curvature along the width of the door. Twist-A deviation in which one or two comers of the door are out of plane with the other comers of the door.

  • White

    When referring to color and matching, veneers containing all sapwood, ranging in color from pink to yellow.

  • Wood Filler

    An aggregate of resin and strands, shreds, or flour of wood, which is used to fill openings in wood and provide a smooth, durable surface.

  • Wood Flush Door

    An assembly consisting of a core and one or more edge bands, with two plies of wood veneer with laminate, wood, or wood derivative on each side. All parts are composed of wood, wood derivatives, fire resistant composites or decorative laminates.

  • Worm Track (Scar)

    Marks caused by various types of wood attacking larvae. Often appear as sound discolorations running with or across the grain in straight to wavy streaks. Sometimes referred to as ‘pith flecks’ in certain species of maple, birch and other hardwoods because of a resemblance to the color of pith.